Please refer to Updating Firmware on the page about our Lobaro Maintenance Tool.

# Changelog
`app-lorawannrf9160-onewire-bridge`temperature`

This changelog's format is based on [Keep a Changelog](https://keepachangelog.com/en/1.0.0/),
and this project adheres to [Semantic Versioning](https://semver.org/spec/v2.0.0.html).  

## 0.52.119 - 20202022-1012-15
### ChangedFixed
- Set standard value for config parameter `LostReboot` to 1 (from 0).

## 0.5.0 - 2020-08-12 RF Switch behavior on LTE join

## 0.2.18 - 2022-12-14
### Fixed
- Confirmation of remote config and firmware updates added

## 0.2.17 - 2022-12-07
### Fixed
- RF Path selection now as expected

## 0.2.16 - 2022-10-07
### Added
- Power-On Selftest Status Packet now contains Modem Information including battery voltage and temperature
### Changed
- BREAKING CHANGE: Default values for `JoinEUI`, `AppKey`, `NwkKey` changed!
- Uses LoRaWAN-Stack that was certified for wMBus-Bridge
- Implement changes in LoRaWAN-Stack that happend during certification. Implements some 
edge-case.
- Make remote config feature robuster, e.g. when sending downlinks with ACK request. Status Packet set to daily at 0h with random minute and second 

## 0.2.15 - 2022-09-26
### Optimized
- Now using High Precision Clock for Onewire Communication
### Added
- Startup Tests

## 0.2.14 - 2022-08-01
### Fixed
- Added missing call to adopt temp config in lorawan

## 0.2.13 - 2022-08-01
### Fixed
- NbTrans behaviour
- a case that added an invalid packet to the queue 
- a bug leading to system restart when trying to send while all channels are blocked
### Optimized
- optimized onewire Timings
- settings for long cables
### Added
- A packet containing just a 0 if no sensor was found  ## 0.2.1 - 2022-03-22
### Changed
- order of config parameters

## 0.2.0 - 2022-03-22
### Added
- nbiot upload
- reboot on lost LoRaWAN connection

## 0.1.3 - 2022-02-18
### Fixed
- Increase power on delay after sleep, so sensors have enough time to convert temperature.

## 0.1.2 - 2202-01-31
### Fixed
- FixedFix Mixupreading of Sensorstesting firmware thatname could(fixes triggerself endlesstest loop`factory`).

## 0.41.1 - 20202022-0701-2131
### Fixed
- Fix payload of Changed
- Revert status message to original port 1 format for backwards compatibility.
- Add Power-On wait between activating sensor power and reading sensor data.

## 0.41.0 - 20202022-0601-3028
### Added
- Start changelog.
### Changed
- Use lobawan stack v1.2.2
- Sensors from `SensorIdOrder` that are missing will still be uploaded (with -0x8000 value)
- When `SendSensorId`==`false` uploads are done on port 3 (was port 2),
- Enable 3.3V step-up only if voltage is below 3.1V (was: if below 3.3V).
- New firmware created from `app-lorawan-onewire-bridge` and `app-nrf9160-onewire-bridge`.
- LoRaWAN upload only (so far).
- Add RemoteConfiguration, TimeSync, and LostReboot feature.
### Changed
- Internal Sensor is now an emulated Sensor with all zero ID that holds the temperature
  measured inside the nrf. Temperature resolution is down to 1°C. Changes should be
  compatible with LoRaWAN format used by LoRaWAN-only 1-wire bridge.
- Change status message to new Lobaro Unified Status Telegram format (on port 64).
  

Please refer to Updating Firmware on the page about our Lobaro Maintenance Tool.

# Changelog
`app-nrf9160-temperature`

This changelog's format is based on [Keep a Changelog](https://keepachangelog.com/en/1.0.0/),
and this project adheres to [Semantic Versioning](https://semver.org/spec/v2.0.0.htmlSupport up to 32 sensors (only 25 supported in `SensorIdOrder`).

## 0.31.3 - 20192022-08-01
- Added ADR config parameter02-18
### Fixed
- Increase power on delay after sleep, so sensors have enough time to convert temperature.

## 0.31.2 - 20192202-08-01
- Fixed Onewire init after DeepSleep01-31
### Fixed
- Fix reading of testing firmware name (fixes self test `factory`).

## 0.31.1 - 20192022-07-2901-31
### Changed
- TempRevert sensorsstatus willmessage beto printedoriginal andport sent1 sortedformat byfor parameter "SensorIdOrder" and by ID or just by ID if parameter "SensorIdOrder" is emptybackwards compatibility.
- Add Power-On wait between activating sensor power and reading sensor data.

## 0.21.0 - 20192022-02-1501-28
### Added
- AddNew firmware parametercreated "SendSensorId" to allow skipping sensor IDs in payload

## 0.0.3
- Bugfixes in LoraWAN stack
- LoRaWAN Support for RX1 DataRate Offset

## 0.0.2
- Don't send sensor type with ID (support 6 sensors in 50 bytes)
- Add TestMode config value
- Add SendInternalTemp config value
- Internal sensor is send first if SendInternalTemp = true

from `app-lorawan-onewire-bridge` and `app-nrf9160-onewire-bridge`.
- LoRaWAN upload only (so far).
- Add RemoteConfiguration, TimeSync, and LostReboot feature.
### Changed
- Internal Sensor is now an emulated Sensor with all zero ID that holds the temperature
  measured inside the nrf. Temperature resolution is down to 1°C. Changes should be
  compatible with LoRaWAN format used by LoRaWAN-only 1-wire bridge.
- Change status message to new Lobaro Unified Status Telegram format (on port 64).